/** ****************************************************************************** * @file stm322xg_eval.h * @author MCD Application Team * @brief This file contains definitions for STM322xG_EVAL's LEDs, * push-buttons and COM ports hardware resources. ****************************************************************************** * @attention * *

© COPYRIGHT(c) 2017 STMicroelectronics

* * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM322xG_EVAL_H #define __STM322xG_EVAL_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32f2xx_hal.h" /** @addtogroup BSP * @{ */ /** @addtogroup STM322xG_EVAL * @{ */ /** @addtogroup STM322xG_EVAL_LOW_LEVEL * @{ */ /** @defgroup STM322xG_EVAL_LOW_LEVEL_Exported_Types STM322xG EVAL LOW LEVEL Exported Types * @{ */ typedef enum { LED1 = 0, LED2 = 1, LED3 = 2, LED4 = 3 }Led_TypeDef; typedef enum { BUTTON_WAKEUP = 0, BUTTON_TAMPER = 1, BUTTON_KEY = 2, BUTTON_RIGHT = 3, BUTTON_LEFT = 4, BUTTON_UP = 5, BUTTON_DOWN = 6, BUTTON_SEL = 7 }Button_TypeDef; typedef enum { BUTTON_MODE_GPIO = 0, BUTTON_MODE_EXTI = 1 }ButtonMode_TypeDef; typedef enum { JOY_MODE_GPIO = 0, JOY_MODE_EXTI = 1 }JOYMode_TypeDef; typedef enum { JOY_NONE = 0, JOY_SEL = 1, JOY_DOWN = 2, JOY_LEFT = 3, JOY_RIGHT = 4, JOY_UP = 5 }JOYState_TypeDef; typedef enum { COM1 = 0, COM2 = 1 }COM_TypeDef; /** * @} */ /** @defgroup STM322xG_EVAL_LOW_LEVEL_Exported_Constants STM322xG EVAL LOW LEVEL Exported Constants * @{ */ /** * @brief Define for STM322xG_EVAL board */ #if !defined (USE_STM322xG_EVAL) #define USE_STM322xG_EVAL #endif /** @addtogroup STM322xG_EVAL_LOW_LEVEL_LED STM322xG EVAL LOW LEVEL LED * @{ */ #define LEDn 4 #define LED1_PIN GPIO_PIN_6 #define LED1_GPIO_PORT GPIOG #define LED1_GPIO_CLK_ENABLE() __HAL_RCC_GPIOG_CLK_ENABLE() #define LED1_GPIO_CLK_DISABLE() __HAL_RCC_GPIOG_CLK_DISABLE() #define LED2_PIN GPIO_PIN_8 #define LED2_GPIO_PORT GPIOG #define LED2_GPIO_CLK_ENABLE() __HAL_RCC_GPIOG_CLK_ENABLE() #define LED2_GPIO_CLK_DISABLE() __HAL_RCC_GPIOG_CLK_DISABLE() #define LED3_PIN GPIO_PIN_9 #define LED3_GPIO_PORT GPIOI #define LED3_GPIO_CLK_ENABLE() __HAL_RCC_GPIOI_CLK_ENABLE() #define LED3_GPIO_CLK_DISABLE() __HAL_RCC_GPIOI_CLK_DISABLE() #define LED4_PIN GPIO_PIN_7 #define LED4_GPIO_PORT GPIOC #define LED4_GPIO_CLK RCC_AHB1Periph_GPIOC #define LED4_GPIO_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() #define LED4_GPIO_CLK_DISABLE() __HAL_RCC_GPIOC_CLK_DISABLE() #define LEDx_GPIO_CLK_ENABLE(__INDEX__) do{if((__INDEX__) == 0) LED1_GPIO_CLK_ENABLE(); else \ if((__INDEX__) == 1) LED2_GPIO_CLK_ENABLE(); else \ if((__INDEX__) == 2) LED3_GPIO_CLK_ENABLE(); else \ if((__INDEX__) == 3) LED4_GPIO_CLK_ENABLE(); \ }while(0) #define LEDx_GPIO_CLK_DISABLE(__INDEX__) do{if((__INDEX__) == 0) LED1_GPIO_CLK_DISABLE(); else \ if((__INDEX__) == 1) LED2_GPIO_CLK_DISABLE(); else \ if((__INDEX__) == 2) LED3_GPIO_CLK_DISABLE(); else \ if((__INDEX__) == 3) LED4_GPIO_CLK_DISABLE(); \ }while(0) /** * @} */ /** @addtogroup STM322xG_EVAL_LOW_LEVEL_BUTTON STM322xG EVAL LOW LEVEL BUTTON * @{ */ /* Joystick pins are connected to IO Expander (accessible through I2C1 interface) */ #define BUTTONn 3 /** * @brief Wakeup push-button */ #define WAKEUP_BUTTON_PIN GPIO_PIN_0 #define WAKEUP_BUTTON_GPIO_PORT GPIOA #define WAKEUP_BUTTON_GPIO_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() #define WAKEUP_BUTTON_GPIO_CLK_DISABLE() __HAL_RCC_GPIOA_CLK_DISABLE() #define WAKEUP_BUTTON_EXTI_IRQn EXTI0_IRQn /** * @brief Tamper push-button */ #define TAMPER_BUTTON_PIN GPIO_PIN_13 #define TAMPER_BUTTON_GPIO_PORT GPIOC #define TAMPER_BUTTON_GPIO_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() #define TAMPER_BUTTON_GPIO_CLK_DISABLE() __HAL_RCC_GPIOC_CLK_DISABLE() #define TAMPER_BUTTON_EXTI_IRQn EXTI15_10_IRQn /** * @brief Key push-button */ #define KEY_BUTTON_PIN GPIO_PIN_15 #define KEY_BUTTON_GPIO_PORT GPIOG #define KEY_BUTTON_GPIO_CLK_ENABLE() __HAL_RCC_GPIOG_CLK_ENABLE() #define KEY_BUTTON_GPIO_CLK_DISABLE() __HAL_RCC_GPIOG_CLK_DISABLE() #define KEY_BUTTON_EXTI_IRQn EXTI15_10_IRQn #define BUTTONx_GPIO_CLK_ENABLE(__INDEX__) do{if((__INDEX__) == 0) WAKEUP_BUTTON_GPIO_CLK_ENABLE(); else \ if((__INDEX__) == 1) TAMPER_BUTTON_GPIO_CLK_ENABLE(); else \ if((__INDEX__) == 2) KEY_BUTTON_GPIO_CLK_ENABLE(); \ }while(0) #define BUTTONx_GPIO_CLK_DISABLE(__INDEX__) do{if((__INDEX__) == 0) WAKEUP_BUTTON_GPIO_CLK_DISABLE(); else \ if((__INDEX__) == 1) TAMPER_BUTTON_GPIO_CLK_DISABLE(); else \ if ((__INDEX__) == 2) KEY_BUTTON_GPIO_CLK_DISABLE(); \ }while(0) /** * @} */ /** @addtogroup STM322xG_EVAL_LOW_LEVEL_COM STM322xG EVAL LOW LEVEL COM * @{ */ #define COMn 1 /** * @brief Definition for COM port1, connected to USART3 */ #define EVAL_COM1 USART3 #define EVAL_COM1_CLK_ENABLE() __HAL_RCC_USART3_CLK_ENABLE() #define EVAL_COM1_CLK_DISABLE() __HAL_RCC_USART3_CLK_DISABLE() #define EVAL_COM1_TX_PIN GPIO_PIN_10 #define EVAL_COM1_TX_GPIO_PORT GPIOC #define EVAL_COM1_TX_GPIO_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() #define EVAL_COM1_TX_GPIO_CLK_DISABLE() __HAL_RCC_GPIOC_CLK_DISABLE() #define EVAL_COM1_TX_AF GPIO_AF7_USART3 #define EVAL_COM1_RX_PIN GPIO_PIN_11 #define EVAL_COM1_RX_GPIO_PORT GPIOC #define EVAL_COM1_RX_GPIO_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() #define EVAL_COM1_RX_GPIO_CLK_DISABLE() __HAL_RCC_GPIOC_CLK_DISABLE() #define EVAL_COM1_RX_AF GPIO_AF7_USART3 #define EVAL_COM1_IRQn USART3_IRQn #define EVAL_COMx_CLK_ENABLE(__INDEX__) do{if((__INDEX__) == 0) EVAL_COM1_CLK_ENABLE(); \ }while(0) #define EVAL_COMx_CLK_DISABLE(__INDEX__) do{if((__INDEX__) == 0) EVAL_COM1_CLK_DISABLE(); \ }while(0) #define EVAL_COMx_TX_GPIO_CLK_ENABLE(__INDEX__) do{if((__INDEX__) == 0) EVAL_COM1_TX_GPIO_CLK_ENABLE(); \ }while(0) #define EVAL_COMx_TX_GPIO_CLK_DISABLE(__INDEX__) do{if((__INDEX__) == 0) EVAL_COM1_TX_GPIO_CLK_DISABLE(); \ }while(0) #define EVAL_COMx_RX_GPIO_CLK_ENABLE(__INDEX__) do{if((__INDEX__) == 0) EVAL_COM1_RX_GPIO_CLK_ENABLE(); \ }while(0) #define EVAL_COMx_RX_GPIO_CLK_DISABLE(__INDEX__) do{if((__INDEX__) == 0) EVAL_COM1_RX_GPIO_CLK_DISABLE(); \ }while(0) /** * @brief Definition for Potentiometer, connected to ADC3 */ #define ADCx ADC3 #define ADCx_CLK_ENABLE() __HAL_RCC_ADC3_CLK_ENABLE() #define ADCx_CHANNEL_GPIO_CLK_ENABLE() __HAL_RCC_GPIOF_CLK_ENABLE() #define ADCx_FORCE_RESET() __HAL_RCC_ADC_FORCE_RESET() #define ADCx_RELEASE_RESET() __HAL_RCC_ADC_RELEASE_RESET() /* Definition for ADCx Channel Pin */ #define ADCx_CHANNEL_PIN GPIO_PIN_9 #define ADCx_CHANNEL_GPIO_PORT GPIOF /* Definition for ADCx's Channel */ #define ADCx_CHANNEL ADC_CHANNEL_7 #define SAMPLINGTIME ADC_SAMPLETIME_3CYCLES #define ADCx_POLL_TIMEOUT 10 /** * @brief Joystick Pins definition */ #define JOY_SEL_PIN IO_PIN_7 #define JOY_DOWN_PIN IO_PIN_6 #define JOY_LEFT_PIN IO_PIN_5 #define JOY_RIGHT_PIN IO_PIN_4 #define JOY_UP_PIN IO_PIN_3 #define JOY_NONE_PIN JOY_ALL_PINS #define JOY_ALL_PINS (IO_PIN_3 | IO_PIN_4 | IO_PIN_5 | IO_PIN_6 | IO_PIN_7) /* Exported constantIO -------------------------------------------------------*/ /* I2C clock speed configuration (in Hz) WARNING: Make sure that this define is not already declared in other files (ie. stm322xg_eval.h file). It can be used in parallel by other modules. */ #ifndef BSP_I2C_SPEED #define BSP_I2C_SPEED 100000 #endif /* BSP_I2C_SPEED */ #define IO_I2C_ADDRESS 0x88 #define TS_I2C_ADDRESS 0x82 #define CAMERA_I2C_ADDRESS 0x60 #define AUDIO_I2C_ADDRESS 0x94 /* For M24C64 devices, E0, E1 and E2 pins are all used for device address selection (no need for additional address lines). According to the Hardware connection on the board (on STM322xG-EVAL board E0 = E1 = E2 = 0) */ #define EEPROM_I2C_ADDRESS 0xA0 /* User can use this section to tailor I2Cx/I2Cx instance used and associated resources */ /* Definition for I2Cx clock resources */ #define EVAL_I2Cx I2C1 #define EVAL_I2Cx_CLK_ENABLE() __HAL_RCC_I2C1_CLK_ENABLE() #define EVAL_DMAx_CLK_ENABLE() __HAL_RCC_DMA1_CLK_ENABLE() #define EVAL_I2Cx_SCL_SDA_GPIO_CLK_ENABLE() __HAL_RCC_GPIOB_CLK_ENABLE() #define EVAL_I2Cx_FORCE_RESET() __HAL_RCC_I2C1_FORCE_RESET() #define EVAL_I2Cx_RELEASE_RESET() __HAL_RCC_I2C1_RELEASE_RESET() /* Definition for I2Cx Pins */ #define EVAL_I2Cx_SCL_PIN GPIO_PIN_6 #define EVAL_I2Cx_SCL_SDA_GPIO_PORT GPIOB #define EVAL_I2Cx_SCL_SDA_AF GPIO_AF4_I2C1 #define EVAL_I2Cx_SDA_PIN GPIO_PIN_9 /* I2C interrupt requests */ #define EVAL_I2Cx_EV_IRQn I2C1_EV_IRQn #define EVAL_I2Cx_ER_IRQn I2C1_ER_IRQn /** * @} */ /** * @} */ /** @defgroup STM322xG_EVAL_LOW_LEVEL_Exported_Functions STM322xG EVAL LOW LEVEL Exported Functions * @{ */ uint32_t BSP_GetVersion(void); void BSP_LED_Init(Led_TypeDef Led); void BSP_LED_On(Led_TypeDef Led); void BSP_LED_Off(Led_TypeDef Led); void BSP_LED_Toggle(Led_TypeDef Led); void BSP_PB_Init(Button_TypeDef Button, ButtonMode_TypeDef Button_Mode); uint32_t BSP_PB_GetState(Button_TypeDef Button); void BSP_COM_Init(COM_TypeDef COM, UART_HandleTypeDef *huart); void BSP_POTENTIOMETER_Init(void); uint32_t BSP_POTENTIOMETER_GetLevel(void); uint8_t BSP_JOY_Init(JOYMode_TypeDef Joy_Mode); JOYState_TypeDef BSP_JOY_GetState(void); /** * @} */ /** * @} */ /** * @} */ /** * @} */ #ifdef __cplusplus } #endif #endif /* __STM322xG_EVAL_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/